50W Vco Signal Generator PA Modules GPS Band L3

Product Details
Customization: Available
Frequency Range: ISM
Frequency: 1350-1450MHz
Still deciding? Get samples of US$ 300/Piece
Request Sample

360° Virtual Tour

Diamond Member Since 2018

Suppliers with verified business licenses

Audited Supplier

Audited by an independent third-party inspection agency

Registered Capital
500000 RMB
Plant Area
501~1000 square meters
Find Similar Products

Basic Info.

Model NO.
2024092901A01
Usage
RF Signal
Material
Silver
Industry
Telecommunication
Signal Source
Scanning Noise Source
Transport Package
Carton
Specification
21*12*5cm
Trademark
OEM, ODM
Origin
Shenzhen
HS Code
8517799000
Production Capacity
5000/Months

Product Description


50W 1.4GHz Satellite Navigation Amplifier with signal source

Main Specification
No. Item Requirements
1  Frequency Range L3: 1350-1450MHz
2 Signal Source  High-speed Scanning Noise Source
3 Max Pout 47dBm±0.5dB 
4 RF Port VSWR ≤1.5
5 Working Voltage 28VDC±1V
6 Working Current <5A
7 RF Connector SMA-Female, 50 Ohms
8 Dimension 210*92*25mm (Exclusive Connector)
9 Power Supply Port Pull-core Capacitor
10 Working Temperature -25----+65ºC
11 Temperature Protection Shutdown more than 75ºC, auto-restart less than 50ºC
12 VSWR Protection Shutdown when reversed power more 25W
13 Power Switch 8mm metal button switch self-locking ,with light waterproof

Monitoring & Control
50W Vco Signal Generator PA Modules GPS Band L3

Competitive Advantage
  1. Output Power is more than 50W over full temperature range (-25ºC to 85ºC) at same Frequency
  2. Output Power is more than 50W over full working Frequency band at same temperature
  3. LDMOS Device ensure low Spurious emission and low Harmonics emission,
  4. Continuous wave output is suitable  for 7*24hours
  5. ALC (Auto Level Control) ensure stable output power over full frequency and full temperature
  6. Select ROGERS Rogers high-frequency printed circuit board (PCB) to ensure stability of Amplifier modules
  7. All screws are made of stainless steel, the amplifier modules are corrosion-resistant
  8. All of devices are new (including final RF power Amplifier),that assure high quality of modules
  9. Isolator is embedded in amplifier modules at output port,  good VSWR and protect PA from damage.
  10. With logarithmic RF Power detector, detector output of forward power and reversed power is linear-in-decibels.   
  11. ALC control function with output power or working current
  12. Protection over High VSWR and shutdown to avoid or reduce the damage from any mismatch
  13. High Temperature Protection and re-start when temperature low down.
  14. With temperature compensation and frequency compensation ,  output power and gain of RF PA is more steady.
  15. Protection over short or open of output port
Remarks
   
  1. It must use a suitable radiator (which enough for PA radiating requirement) and a radiating system with Fans, otherwise it will shut down by over high-temperature. 
  2. When install PA, please inspect bottom surface of Radiator is very smooth and spread on Thermal grease with above 4.0 thermal conductivity.
  3. Pout  should be connect to a probably Load, Attenuator or antenna (50 ohms, more than 100W handling Power, lower than VSWR 2.0). 
  4. Long time output short circuit or open circuit might damage PA.
  5. RF Input and RF Output connector cannot be pull out or plug with Power on.
  6. If working voltage is reversed polarity to PA, PA would be damaged.
  7. Working Voltage:Normal working Voltage:26-29VDC;
  8. We suggest the maximum working temperature for PA surface no more than 75ºC.

 

Send your message to this supplier

*From:
*To:
*Message:

Enter between 20 to 4,000 characters.

This is not what you are looking for? Post a Sourcing Request Now
Contact Supplier